Skip to content

How to schedule a multi-bay shop without double-booking the lift

Most scheduling messes in a multi-bay shop come from one mistake: treating every bay as interchangeable. Here’s a practical way to match jobs to the bays that can actually do them — and keep your specialised bays free for the work that needs them.

4 min readThe BayLane team

On this page
  1. 1. Write down what each bay can actually do
  2. 2. Write down what each job needs
  3. 3. Book the job into the simplest bay that can do it
  4. 4. Plan the time the bay is busy, not just the labour
  5. 5. Hold the bay for multi-day jobs
  6. 6. Look at the board, not a list
  7. 7. When a job finishes early, free the bay
  8. Where BayLane fits

Every multi-bay shop has a version of this morning: two cars that both need the lift, one alignment that got booked into the only bay without a rack, and a full-detail sitting in the bay the brake job was supposed to use. Nobody did anything wrong — the calendar just didn’t know what each bay could do.

A paper book, a whiteboard or a generic calendar treats a bay as “a slot”. Your shop doesn’t work that way. Bays have equipment, and jobs need it. Here’s how to schedule around that, whatever software you use.

1. Write down what each bay can actually do

Walk the floor and list every bay with the equipment that matters for booking. Keep it to things that decide whether a job can happen there, not everything on the wall:

  • Lifts: two-post, four-post, scissor, or none.
  • Specialised gear: alignment rack, tire machine and balancer, A/C machine, frame equipment, paint booth.
  • Environment: a clean, enclosed bay for paint protection film or coatings; good lighting for paint correction; a wash bay with drainage.
  • Size limits: ceiling height for lifted trucks, a bay long enough for a crew-cab dually.

Most shops find two or three “special” bays and several general ones. That split is the whole game.

2. Write down what each job needs

Now go through your service menu and note the equipment each service requires. An oil change needs a lift (or a pit). An alignment needs the rack. A tire mount-and-balance needs the tire machine and balancer, and a lift if you’re pulling wheels. A ceramic coating needs an enclosed, clean bay.

Be strict about “requires” versus “nice to have”. If a brake job can be done on a four-post but is much easier on a two-post, decide which one counts — and write it down so the front desk isn’t guessing.

3. Book the job into the simplest bay that can do it

This is the rule that stops the lift from being double-booked: when more than one bay qualifies, put the work in the least-equipped one. An oil change that fits on a basic lift shouldn’t take the bay with the alignment rack just because it was free at 9:00. Fill the general bays first and the specialised bays stay open for the jobs only they can do.

It feels backwards on a slow morning — the alignment bay is right there — but the 11:00 walk-in alignment is the reason not to. A shop that books this way turns away far fewer jobs on busy days.

4. Plan the time the bay is busy, not just the labour

A 1.5-hour brake job doesn’t free the bay after 1.5 hours. There’s pulling the car in, the test drive, cleanup, and the car waiting for the customer. Two numbers matter for every service:

NumberWhat it meansExample
Work timeHours a tech is actually on the job1.5 h brake pads and rotors
Bay timeHow long the bay is taken, start to finish2 h including pull-in, test drive and cleanup

Schedule on bay time. If you schedule on work time, the board looks fine at 8:00 and is an hour behind by lunch.

5. Hold the bay for multi-day jobs

Some work owns a bay for days: a waiting-on-parts repair you can’t move, a coating that has to cure indoors, a full-body film install. Block the bay for the whole stretch — including nights — rather than booking “around” it and hoping. A car that can’t be moved is still occupying the bay even when nobody is working on it.

6. Look at the board, not a list

A list of appointments hides conflicts; a board with one lane per bay shows them. When every bay is a lane and every job is a block, you see the gap at 2:00 in bay 3, the alignment rack sitting empty, and the job that’s about to run into the next one.

Make the board the first thing the front desk checks before saying yes to a walk-in — and the thing the techs look at to know what’s next.

7. When a job finishes early, free the bay

Jobs don’t always run long. When a car is done early and moved out, release the rest of its time so the next job — or a walk-in — can take the bay. Shops that do this consistently find an extra job or two a day they used to miss.

Where BayLane fits

This is the problem BayLane was built for. You tell it what equipment each bay has and what each service needs; when you book, it only offers times in bays that can actually do the job, and it fills the simplest qualifying bay first. Bay time includes your buffers, multi-day jobs hold the bay overnight, and the lane board shows every bay at a glance — including on a TV in the shop.

Whether you use BayLane or a whiteboard, the method is the same: know what each bay can do, know what each job needs, and never let a simple job take a special bay.

More like this, in your inbox

New guides for running a busy shop and what’s new in BayLane. A few emails a month at most.

No spam. Unsubscribe from any email in one click.

PPF and ceramic cure times: planning bays for multi-day jobs

Paint protection film and ceramic coatings don’t end when the installer puts the tools down. Cure time decides when a car can leave — and how long it owns the bay. Here’s how detail and protection shops plan multi-day work without stalling the rest of the schedule.

3 min readThe BayLane team